• CE交换机 vxlan(五)


    [root@bogon ~]# ip netns exec ns2 ping 10.0.10.12
    PING 10.0.10.12 (10.0.10.12) 56(84) bytes of data.
    From 10.0.10.123 icmp_seq=1 Destination Host Unreachable
    ^C
    --- 10.0.10.12 ping statistics ---
    3 packets transmitted, 0 received, +1 errors, 100% packet loss, time 2067ms
    
    [root@bogon ~]#
    <ZZKK>capture-packet interface 100GE 1/0/58 destination terminal          --------------抓不到包
    Warning: Capture-packet will be shown on terminal.
    <ZZKK>undo capture-packet
    
      ------------------capture report-----------------------
    
      Capture-Packet Index 1
      Type        : forwarding
      Interface   : 100GE1/0/58
      Direction   : inbound
      Time-out    : 60 seconds
      Packet-num  : 100
      Packet-len  : 64
      BufferOnly  : disabled
    
      -------------------------------------------------------
    <ZZKK>

    节点1

    ip link add vxlan3300 type vxlan id 3300  remote 10.10.30.253  dstport 4789 dev enahisic2i0
    ip link set vxlan3300 up
    brctl addif br1 vxlan3300
    [root@bogon ~]# ip netns exec ns2 ip a
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
        link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
        inet 127.0.0.1/8 scope host lo
           valid_lft forever preferred_lft forever
        inet6 ::1/128 scope host 
           valid_lft forever preferred_lft forever
    2: nstap2.vlan100@nstap2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
        link/ether c6:9a:46:bd:18:14 brd ff:ff:ff:ff:ff:ff
    128: nstap2@if127: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
        link/ether c6:9a:46:bd:18:14 brd ff:ff:ff:ff:ff:ff link-netnsid 0
        inet 172.16.103.99/24 scope global nstap2
           valid_lft forever preferred_lft forever
    [root@bogon ~]#
    [root@bogon ~]# ip netns exec ns2 ping  172.16.103.6
    PING 172.16.103.6 (172.16.103.6) 56(84) bytes of data.
    64 bytes from 172.16.103.6: icmp_seq=1 ttl=64 time=0.188 ms
    64 bytes from 172.16.103.6: icmp_seq=2 ttl=64 time=0.145 ms
    64 bytes from 172.16.103.6: icmp_seq=3 ttl=64 time=0.163 ms
    ^C
    --- 172.16.103.6 ping statistics ---
    3 packets transmitted, 3 received, 0% packet loss, time 2068ms
    rtt min/avg/max/mdev = 0.145/0.165/0.188/0.020 ms
    [root@bogon ~]# 

    节点1 tcpdump

    [root@bogon ~]# tcpdump -i enahisic2i0  dst port 4789 -env
    tcpdump: listening on enahisic2i0, link-type EN10MB (Ethernet), capture size 262144 bytes
    14:48:07.504542 48:57:02:64:ea:1b > f4:1d:6b:87:53:2a, ethertype IPv4 (0x0800), length 160: (tos 0x0, ttl 64, id 28221, offset 0, flags [none], proto UDP (17), length 146)
        10.10.16.81.56748 > 10.10.30.253.4789: VXLAN, flags [I] (0x08), vni 3300
    56:f2:48:64:ad:38 > 33:33:00:00:00:16, ethertype IPv6 (0x86dd), length 110: (hlim 1, next-header Options (0) payload length: 56) :: > ff02::16: HBH (rtalert: 0x0000) (padn) [icmp6 sum ok] ICMP6, multicast listener report v2, 2 group record(s) [gaddr ff02::1:ff64:ad38 to_ex, 0 source(s)] [gaddr ff02::2 to_ex, 0 source(s)]
    14:48:07.774531 48:57:02:64:ea:1b > f4:1d:6b:87:53:2a, ethertype IPv4 (0x0800), length 160: (tos 0x0, ttl 64, id 28226, offset 0, flags [none], proto UDP (17), length 146)

    节点2

    [~JG05-SA-01-CE8850]bridge-domain 100
    [*JG05-SA-01-CE8850-bd100]vxlan vni 3300
    Info: Please disable dynamic ARP learning when the controller is used to deliver ARP entries.
    [*JG05-SA-01-CE8850-bd100]quit
    [*JG05-SA-01-CE8850]interface nve nve1
                                      ^
    Error: Wrong parameter found at '^' position.
    [*JG05-SA-01-CE8850]interface nve1    
    Info: Ensure that the IP addresses and MAC addresses of the NVE interfaces on Devices are the same, as they are dual-active gateways using M-LAG.
    [*JG05-SA-01-CE8850-Nve1]source 10.10.30.253
    [*JG05-SA-01-CE8850-Nve1]vni 3300 head-end peer-list 10.10.16.81
    [*JG05-SA-01-CE8850-Nve1]quit
    [*JG05-SA-01-CE8850]interface  100GE1/0/14 mode l2
                                               ^
    Error: Wrong parameter found at '^' position.
    [*JG05-SA-01-CE8850]interface  100GE1/0/14.1 mode l2
    [*JG05-SA-01-CE8850-100GE1/0/14.1]encapsulation untag
    Warning: Exercise caution when configuring an untagged default sub-interface and ensure that no configurations exist on the main interface before you configure an untagged default sub-interface. Otherwise, it will produce unpredictable results.
    [*JG05-SA-01-CE8850-100GE1/0/14.1]bridge-domain 100
    [*JG05-SA-01-CE8850-100GE1/0/14.1]quit  
    [*JG05-SA-01-CE8850]commit
    [~JG05-SA-01-CE8850]quit
    <JG05-SA-01-CE8850>dis vxlan tunnel
    Number of vxlan tunnel : 1
    Tunnel ID   Source                Destination           State  Type     Uptime
    -----------------------------------------------------------------------------------
    4026531841  10.10.30.253          10.10.16.81           up     static   00:00:11  
    <JG05-SA-01-CE8850>
    <JG05-SA-01-CE8850>dis ip in br    
    *down: administratively down
    !down: FIB overload down
    ^down: standby
    (l): loopback
    (s): spoofing
    (d): Dampening Suppressed
    The number of interface that is UP in Physical is 2
    The number of interface that is DOWN in Physical is 1
    The number of interface that is UP in Protocol is 2
    The number of interface that is DOWN in Protocol is 1
    Interface                   IP Address/Mask    Physical Protocol VPN           
    MEth0/0/0                   192.168.1.1/24     down     down     --            
    NULL0                       unassigned         up       up(s)    --            
    Vlanif1030                  10.10.30.253/24    up       up       --            
    .
    <JG05-SA-01-CE8850>dis current-config int vlanif1030
    #
    interface Vlanif1030
     ip address 10.10.30.253 255.255.255.0
    #
    return
    <JG05-SA-01-CE8850>
  • 相关阅读:
    承载进程 (vshost.exe)
    命令行生成解决方案
    【SQL Server】存储过程的设计概念(3)TSQL的编译和执行过程
    .NET Framework 4
    reflector最新说明
    应用程序域
    vi 编辑器的用法(2013最新整理)
    linux中查看日志的方法
    修改linux主机名的方法介绍
    如何获得桌面上任意一个位置的颜色的 rgb 或者16进制值了
  • 原文地址:https://www.cnblogs.com/dream397/p/13280805.html
Copyright © 2020-2023  润新知