最新需要使用硬盘做一些测试，需要使用到hdparm工具，并进行了解，并进行简要记录；
hdparm、dd、fio、都是很好的硬盘测试软件；通常使用其对硬盘信息做基本了解；
关闭硬盘写Cache用例：
hdparm -W /dev/sdh # 查看写缓存状态； hdparm -W 0 /dev/sdh # 关闭Cache,保证数据强一致性；放置断电时数据未落盘； hdparm -W 1 /dev/sdh # 打开
测试磁盘和磁盘缓存读取速度：
查看磁盘信息： fdisk -l /dev/sdh hdparm /dev/sdh
评估磁盘读取速度：
hdparm -t /dev/sdh
评估磁盘缓存读取速度：
hdparm -T /dev/sdh
直接测试硬盘的读性能(绕过内核页缓存)：
hdparm -tT --direct /dev/sdh
顺序写测试：
time -p bash -c "dd if=/dev/urandom of=./dd.log bs=1M count=50000"
随机写测试(使用direct标识，绕过页缓存)：
fio -filename=randw-singlethread -fallocate=none -direct=1 -iodepth 1 -thread -rw=randwrite -ioengine=libaio -bs=32k -size=1000M -runtime=30s -numjobs=1 -name=hdparm-randwsinglethread
命令使用方法说明：
hdparm -h hdparm - get/set hard disk parameters - version v9.43, by Mark Lord. Usage: hdparm [options] [device ...] Options: -a Get/set fs readahead -A Get/set the drive look-ahead flag (0/1) -b Get/set bus state (0 == off, 1 == on, 2 == tristate) -B Set Advanced Power Management setting (1-255) -c Get/set IDE 32-bit IO setting -C Check drive power mode status -d Get/set using_dma flag -D Enable/disable drive defect management -E Set cd/dvd drive speed -f Flush buffer cache for device on exit -F Flush drive write cache -g Display drive geometry -h Display terse usage information -H Read temperature from drive (Hitachi only) -i Display drive identification -I Detailed/current information directly from drive -J Get/set Western DIgital "Idle3" timeout for a WDC "Green" drive (DANGEROUS) -k Get/set keep_settings_over_reset flag (0/1) -K Set drive keep_features_over_reset flag (0/1) -L Set drive doorlock (0/1) (removable harddisks only) -m Get/set multiple sector count -M Get/set acoustic management (0-254, 128: quiet, 254: fast) -n Get/set ignore-write-errors flag (0/1) -N Get/set max visible number of sectors (HPA) (VERY DANGEROUS) -p Set PIO mode on IDE interface chipset (0,1,2,3,4,...) -P Set drive prefetch count -q Change next setting quietly -Q Get/set DMA queue_depth (if supported) -r Get/set device readonly flag (DANGEROUS to set) -R Get/set device write-read-verify flag -s Set power-up in standby flag (0/1) (DANGEROUS) -S Set standby (spindown) timeout -t Perform device read timings -T Perform cache read timings -u Get/set unmaskirq flag (0/1) -U Obsolete -v Use defaults; same as -acdgkmur for IDE drives -V Display program version and exit immediately -w Perform device reset (DANGEROUS) -W Get/set drive write-caching flag (0/1) -x Obsolete -X Set IDE xfer mode (DANGEROUS) -y Put drive in standby mode -Y Put drive to sleep -z Re-read partition table -Z Disable Seagate auto-powersaving mode --dco-freeze Freeze/lock current device configuration until next power cycle --dco-identify Read/dump device configuration identify data --dco-restore Reset device configuration back to factory defaults --direct Use O_DIRECT to bypass page cache for timings --drq-hsm-error Crash system with a "stuck DRQ" error (VERY DANGEROUS) --fallocate Create a file without writing data to disk --fibmap Show device extents (and fragmentation) for a file --fwdownload Download firmware file to drive (EXTREMELY DANGEROUS) --fwdownload-mode3 Download firmware using min-size segments (EXTREMELY DANGEROUS) --fwdownload-mode3-max Download firmware using max-size segments (EXTREMELY DANGEROUS) --fwdownload-mode7 Download firmware using a single segment (EXTREMELY DANGEROUS) --idle-immediate Idle drive immediately --idle-unload Idle immediately and unload heads --Istdin Read identify data from stdin as ASCII hex --Istdout Write identify data to stdout as ASCII hex --make-bad-sector Deliberately corrupt a sector directly on the media (VERY DANGEROUS) --offset use with -t, to begin timings at given offset (in GiB) from start of drive --prefer-ata12 Use 12-byte (instead of 16-byte) SAT commands when possible --read-sector Read and dump (in hex) a sector directly from the media --repair-sector Alias for the --write-sector option (VERY DANGEROUS) --security-help Display help for ATA security commands --trim-sector-ranges Tell SSD firmware to discard unneeded data sectors: lba:count .. --trim-sector-ranges-stdin Same as above, but reads lba:count pairs from stdin --verbose Display extra diagnostics from some commands --write-sector Repair/overwrite a (possibly bad) sector directly on the media (VERY DANGEROUS)
保持更新，更多内容请关注cnblogs.com/xuyaowen;