• CentOS 7 网卡子接口的创建


    转自:https://www.cnblogs.com/horizonli/p/6093540.html

    OS:CentOS 7
    在linux上创建vlan需要加载802.1q模块:
    1.检测OS是否已经加载802.1q模块
     
     
    [root@controller ~]# modinfo 8021q
    filename:       /lib/modules/3.10.0-229.14.1.el7.x86_64/kernel/net/8021q/8021q.ko
    version:        1.8
    license:        GPL
    alias:          rtnl-link-vlan
    rhelversion:    7.1
    srcversion:     2C3C3989B54002FAEC13FFD
    depends:        mrp,garp
    intree:         Y
    vermagic:       3.10.0-229.14.1.el7.x86_64 SMP mod_unload modversions
    signer:         CentOS Linux kernel signing key
    sig_key:        E9:9F:C4:37:BD:9C:BF:B4:F1:B1:DA:87:C1:57:FF:66:56:9B:EE:66
    sig_hashalgo:   sha256或者:[root@controller ~]# modinfo -F filename 8021q

    /lib/modules/3.10.0-229.14.1.el7.x86_64/kernel/net/8021q/8021q.ko

    或者:

    [root@controller ~]# modprobe --first-time 8021q
    modprobe: ERROR: could not insert '8021q': Module already in kernel

    2.如果没有加载802.1q模块怎么加载?

    ##加载8021q模块
    [root@controller ~]# modprobe 8021q<br>##查看是否正常加载

     [root@controller ~]# lsmod |grep 8021q
      8021q 28808 0
      garp 14384 1 8021q
      mrp 18542 1 8021q

    3.在父接口创建vlan子接口

     3.1在父接口/etc/sysconfig/network-scripts/ifcfg-ethX  中设置 

    DEVICE=ethX
    TYPE=Ethernet
    BOOTPROTO=none
    ONBOOT=yes

    3.2复制父接口并修改接口名称

    cp /etc/sysconfig/network-scripts/ifcfg-ethX /etc/sysconfig/network-scripts/ifcfg-ethX.125     ## X后面的125为vlan号

    3.3配置/etc/sysconfig/network-scripts/ifcfg-ethX.125

     

    DEVICE=ethX.192
    BOOTPROTO=none
    ONBOOT=yes
    IPADDR=192.168.1.1
    PREFIX=24
    NETWORK=192.168.1.0
    VLAN=yes                ##开启vlan,表明此子接口为vlan接口

    4.重启网络

    systemctl restart network
    ================================================
    CONFIGURE 802.1Q VLAN TAGGING USING THE COMMAND LINE
    In Red Hat Enterprise Linux 7, the 8021q module is loaded by default. If necessary, you can make sure that the module is loaded by issuing the following command as root:
     
     
    ~]# modprobe --first-time 8021q
    modprobe: ERROR: could not insert '8021q': Module already in kernel
    
    To display information about the module, issue the following command:
    
    ~]$ modinfo 8021q
    
    See the modprobe(8) man page for more command options.
     
    7.4.1. Setting Up 802.1Q VLAN Tagging Using ifcfg Files
    1.Configure the parent interface in /etc/sysconfig/network-scripts/ifcfg-ethX, whereX is a unique number corresponding to a specific interface,as follows:
     
     
    DEVICE=ethX
    TYPE=Ethernet
    BOOTPROTO=none
    ONBOOT=yes

    2.Configure the VLAN interface configuration in the /etc/sysconfig/network-scripts/directory. The configuration file name should be the parent interface plus a . character plus the VLAN ID number. For example, if the VLAN ID is 192, and the parent interface is eth0, then the configuration file name should be ifcfg-eth0.192:

    DEVICE=ethX.192
    BOOTPROTO=none
    ONBOOT=yes
    IPADDR=192.168.1.1
    PREFIX=24
    NETWORK=192.168.1.0
    VLAN=yes

    If there is a need to configure a second VLAN, with for example, VLAN ID 193, on the same interface, eth0, add a new file with the name eth0.193 with the VLAN configuration details.

    3.Restart the networking service in order for the changes to take effect. As root issue the following command:

    ~]# systemctl restart network

    7.4.2. Configure 802.1Q VLAN Tagging Using ip Commands

    To create an 802.1Q VLAN interface on Ethernet interface eth0, with name VLAN8 and ID 8, issue a command as root as follows:

     
    ~]# ip link add link eth0 name eth0.8 type vlan id 8

    To view the VLAN, issue the following command:

    ~]$ ip -d link show eth0.8
    4: eth0.8@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT
         link/ether 52:54:00:ce:5f:6c brd ff:ff:ff:ff:ff:ff promiscuity 0
         vlan protocol 802.1Q id 8 <REORDER_HDR>

    Note that the ip utility interprets the VLAN ID as a hexadecimal value if it is preceded by 0x and as an octal value if it has a leading 0. This means that in order to assign a VLAN ID with a decimal value of 22, you must not add any leading zeros.

    To remove the VLAN, issue a command as root as follows:

    ~]# ip link delete eth0.8
    ================
    总结:修改父接口的BOOTPROTO=manual
    复制父接口,
    清空内容
    注入下面的内容:
    DEVICE=${SECONF_ETH}.${EXTERNAL_TENANT_NETWORK_VLAN_ID}
    BOOTPROTO=none
    ONBOOT=yes
    IPADDR=${SECOND_SUB_INTERFACE_IP}
    PREFIX=24
    NETWORK=${SECOND_SUB_INTERFACE_NET}
    VLAN=yes
     
     
     
     
     
  • 相关阅读:
    Python iter() 函数
    Python file() 函数
    Python bin() 函数
    QTP自动化测试-打开运行报告
    mysql-笔记-数据类型
    mysql-笔记--增删改查
    mysql-笔记-命名、索引规范
    Navicat for MySQL 安装和破解
    mysql client--笔记-修改密码-登录-查看数据库-创建数据库
    安装mysql
  • 原文地址:https://www.cnblogs.com/zhongguiyao/p/8067791.html
Copyright © 2020-2023  润新知