• BeeProg2C Extremely fast universal USB interfaced programmer


    http://www.elnec.com/products/universal-programmers/beeprog2c/

    • FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Improved pin drivers drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.
    • The programmer performs device insertion test (wrong or backward position) and contact check (poor contact pin-to-socket) before it programs each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
    • The selftest capability allow to run diagnostic part of software to thoroughly check the health of the programmer.
    • Built-in protection circuits eliminate damage of programmer and/or programmed device due to environment or operator failure. All the inputs of the BeeProg2C programmer, including the ZIF socket, connection to PC and power supply input, are protected against ESD up to 15kV.
    • BeeProg2C programmer performs programming verification at the marginal level of supply voltage, which, obviously, improves programming yield, and guarantees long data retention.
    • Various programming adapters are available to handle device in PLCC, JLCC, SOIC, SDIP, SOP, PSOP, SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA, EBGA, FBGA, VFBGA, UBGA, FTBGA, LAP, CSP, SCSP, LQFP, MQFP, HVQFN, QLP, QIP and other packages.
    • USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate
    • FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate (useable after upgrade to BeeProg2)
    • on-board intelligence: powerful microprocessor and FPGA based state machine
    • three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
    • VCCP range 0..8V/1A
    • VPP1, VPP2 range 0..26V/1A
    • autocalibration
    • selftest capability
    • protection against surge and ESD on power supply input, parallel port connection
    • banana jack for ESD wrist straps connection
    • banana jack for connection to ground

    ZIF socket, pindriver

    • 48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 48-pin
    • pindrivers: 48 universal
    • VCCP/VPP1/VPP2 can be connected to each pin
    • perfect ground for each pin
    • FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
    • analog pindriver output level selectable from 1.8 V up to 26V
    • current limitation, overcurrent shutdown, power failure shutdown
    • ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
    • continuity test: each pin is tested before every programming operation

    ISP connector

    • 20-pin male type with missinsertion lock
    • 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage including) devices.
    • 1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
    • programmed chip voltage (VCCP) with both source/sink capability and voltage sense
    • 1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
    • target system supply voltage (range 2V..6V/250mA)
    • ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
    • two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)
    • input signal, switch YES! equivalent (active level: max 0.8V)
  • 相关阅读:
    简单的sql注入3
    简单的sql注入2
    简单的sql注入1
    python安装request及更新pip
    kali linux上安装ssh
    看起来有点难
    猫抓老鼠
    头有点大
    貌似有点难
    这个看起来有点简单!
  • 原文地址:https://www.cnblogs.com/shangdawei/p/3188709.html
Copyright © 2020-2023  润新知