• n2n搭建手记-1-V1


    搭建环境

    supernode :阿里云主机一台 aly1(Centos 6.5)

    edg2node:美团云机器两台 mty1,mty2(Centos 7.0)

     Step-1 各机器安装subviersion 并编译安装n2n_v1

    #很重要,确保gcc和ssl版本一致,

    yum install subversion gcc-c++ openssl-devel

    svn co https://svn.ntop.org/svn/ntop/trunk/n2n
    cd n2n/n2n_v1/

    make && make install
    cp supernode /usr/sbin/
    cp edge /usr/sbin/

    Step-2 中心节点super aly1 开启服务和端口

    远程登录至aly1

    vim /etc/sysconfig/iptables
    *filter下配置

    -A INPUT -p tcp -m tcp --dport 1000 -j ACCEPT

    iptables save

    #启动supernode (注:此处开放端口在配置边缘节点机器时用)

    supernode -l 1000 -v >/dev/null &

    Step-3配置边缘节点机器

     分别登录两台美团云机器,设置边缘节点(xxx.xxx.xxx.xxx:1000 即为阿里云super机器ip)

    边缘节点1

    edge -d n2n0 -c mynetwork -k encryptme -a 10.0.0.1 -l xxx.xxx.xxx.xxx:1000 >/dev/null &

    边缘节点2

    edge -d n2n0 -c mynetwork -k encryptme -a 10.0.0.2 -l xxx.xxx.xxx.xxx:1000 >/dev/null &

    Step-4 验证n2n网络通讯

    在节点1 ping 10.0.0.2 ,在节点2 ping 10.0.0.1 网络正常。

    ssh 10.0.0.x可互联。

    n2n网络搭建完成。

    ------------ -------------- --------------- ----------------- ------------------ -----------

    n2n的命令详解

     1 edge -d <tun device> -a <tun IP address> -c <community> -k <encrypt key> -s <netmask> [-u <uid> -g <gid>][-f][-m <MAC address>]  
     2 -l <supernode host:port> [-p <local port>] [-M <mtu>] [-t] [-r] [-v] [-b] [-h]  
     3   
     4 -d <tun device>          | tun device name  
     5 -a <tun IP address>      | n2n IP address  
     6 -c <community>           | n2n community name  
     7 -k <encrypt key>         | Encryption key (ASCII) - also N2N_KEY=<encrypt key>  
     8 -s <netmask>             | Edge interface netmask in dotted decimal notation (255.255.255.0)  
     9 -l <supernode host:port> | Supernode IP:port  
    10 -b                       | Periodically resolve supernode IP  
    11                          | (when supernodes are running on dynamic IPs)  
    12 -p <local port>          | Local port used for connecting to supernode  
    13 -u <UID>                 | User ID (numeric) to use when privileges are dropped  
    14 -g <GID>                 | Group ID (numeric) to use when privileges are dropped  
    15 -f                       | Fork and run as a daemon. Use syslog.  
    16 -m <MAC address>         | Choose a MAC address for the TAP interface  
    17                          | eg. -m 01:02:03:04:05:06  
    18 -M <mtu>                 | Specify n2n MTU (default 1400)  
    19 -t                       | Use http tunneling (experimental)  
    20 -r                       | Enable packet forwarding through n2n community  
    21 -v                       | Verbose  
  • 相关阅读:
    如何判断轮廓是否为圆(算法更新)
    近期购置的CV&AI类图书梳理
    基于OpenCV实现“钢管计数”算法,基于Csharp编写界面,并实现算法融合
    大厂们的 redis 集群方案
    redis 突然大量逐出导致读写请求block
    Docker 1.13 管理命令
    玩转 Ceph 的正确姿势
    Docker 常用命令
    git常用命令
    从C++到GO
  • 原文地址:https://www.cnblogs.com/mousean/p/6006597.html
Copyright © 2020-2023  润新知