lmhostid获取hostid为空问题

lmhostid获取hostid为空问题

问题描写叙述

今天迁移曾经的一个装有flexlm的虚拟机，结果发如今迁移后启动时报错

... Wrong hostid on SERVER line for license file
...
... SERVER line says 00e081787ba8, hostid is (Cannot get hostid of type 2 [])
... Invalid hostid on SERVER line

解决的方法

从问题描写叙述看，好像是取到hostid有问题，用lmhostid检查一下，发现取到的hostid为”“

./lmhostid 
lmhostid - Copyright (c) 1989-2004 by Macrovision Corporation. All rights reserved.
The FLEXlm host ID of this machine is ""

因为FLEXlm会使用第一块网卡（eth0）的mac地址做hostid，所以用ifconfig检查网络配置。发现当中没有eth0。例如以下：

eth1      Link encap:Ethernet  HWaddr 00:E0:81:78:7B:A8  
          inet addr:192.168.0.88  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::2e0:81ff:fe78:7ba8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2463804 errors:0 dropped:0 overruns:0 frame:0
          TX packets:345560 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:924819172 (881.9 MiB)  TX bytes:34087357 (32.5 MiB)
          Interrupt:11 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:2843863 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2843863 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:729294023 (695.5 MiB)  TX bytes:729294023 (695.5 MiB)

可是在用linux自带网络配置工具和/etc/sysconfig/network-scripts/下的文件配置看。确实是用的eth0。这说明配置出现了不一致问题。

最后。检查/etc/udev/rules.d/70-persistent-net.rules文件

# PCI device 0x1af4:0x1000 (virtio-pci)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*l", ATTR{address}=="00:e0:81:78:7b:a8", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"

# PCI device 0x10ec:0x8139 (8139cp)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:e0:81:78:7b:a8", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"

发现了问题，里面有两个网卡配置项。果断改动为

# PCI device 0x10ec:0x8139 (8139cp)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?
*", ATTR{address}=="00:e0:81:78:7b:a8", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"

然后又一次启动机器。问题解决。

转载请以链接形式标明本文地址
本文地址：http://blog.csdn.net/kongxx/article/details/50480696