mtk android lcm调试

参考MTK 文档LCM_Customer_document_MT6575.pdf

The following shows the steps to add a new LCM driver: 

(1)  Create LCM driver folder $LCM in alps/mediatek/custom/common/kernel/lcm/

(2)  Create LCM driver source file $LCM.c in alps/mediatek/custom/common/kernel/lcm/$LCM

(3)  Implement LCM driver and export lcm_driver_list/lcm_count variables. 

                    

Adaptive LCM Support 
At first you should add you new lcm driver as listed in the previous section, and then add the 
adaptive support: 
1.  Modify the adaptive lcm driver common file:  
alps/mediatek/custom/common/kernel/lcm/mt65xx_lcm_list.c

2.  Add the new LCM driver global variables as shown in the figure below: 

                

3.  [VERY IMPORTANT] Please delete the unused LCM driver folder in the customization folder, 
such as shown in the figure below: 

              

4. But what if I didn’t delete the folders un-usable? The code size will increase, because the 
other LCM drivers will be compiled into codebase too; And if your project doesn’t define 
GPIO usage for serial interface, there will be build error.

5.  Modify the project makefile alps/mediate/config/(project)/ProjetConfig.mk 
Modify CUSTOM_KERNEL_LCM=mt65xx 
Modify CUSTOM_UBOOT_LCM=mt65xx

Case Study – DBI Interface LCM Driver Porting 

In this chapter, we’ll go through a real case study of DBI LCM driver porting. 

LCM specifications: 
  LCM Drive IC: hx8369 
  Interface: 24-bit 80 system bus interface 
  LCD size: 480*800 
  
1.  Create LCM driver folder and LCM driver source file 
alps/mediatek/custom/common/kernel/lcm/hx8369/lcm_dr.c 

2.  Modify the project makefile alps/mtk/make/$(project).mak 
Add CUSTOM_KERNEL_LCM= hx8369 
Add CUSTOM_UBOOT_LCM= hx8369 

3.  Fill the LCM parameters 
A.  Configure the basic information according to the HW connection, LCM type and LCM size: 

                 

MT6575 LCD IO selection is as shown in following table. LCD data pin can share between DPI and NAND data pin 

            

For example, we use 24bits DBI interface LCM, and connect LCM data pin to MT6575 baseband 
Pin DPIR[7:0], DPIG[7:0], DPIB[7:0]. So we must set io_select_mode to be 1; if connect LCM data 
pin to Nand IF, we must set io_select_mode to be 0

B.  Configure data format according to the RGB data pin assignment of the LCM datasheet 

            

C.  Configure LCM waveform timing according to the requirement specified in the LCM datasheet

              

Note: MT6575 LCD controller clock frequency is 130MHz, so clock cycle time is 1/130MHz = 7.69ns

4.  Implement LCM init function 

According the init process specified in LCM datasheet, pull down/up the reset pin, delay and set 
LCM init register settings. 

5.  Implement LCM update function 
Send the block update commands to LCM 

6.  Implement LCM suspend/resume functions 
Send suspend/resume commands to LCM

7. Rebuild uboot and kernel 
In the root directory: 
./mk $(project) gen_cust 
./mk $(project) remake uboot/kernel 
./mk $(project) bootimage 

参考代码：

/*****************************************************************************
*  Copyright Statement:
*  --------------------
*  This software is protected by Copyright and the information
 contained
*  herein is confidential. The software may not be copied
 and the information
*  contained herein may not be used or disclosed except
 with the written
*  permission of MediaTek Inc. (C) 2008
*
*  BY OPENING THIS FILE, BUYER HEREBY UNEQUIVOCALLY ACKNOWLEDGES
 AND AGREES
*  THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK
 SOFTWARE")
*  RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE
 PROVIDED TO BUYER ON
*  AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS
 ANY AND ALL WARRANTIES,
*  EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
 IMPLIED WARRANTIES OF
*  MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR
 NONINFRINGEMENT.
*  NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER
 WITH RESPECT TO THE
*  SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED
 IN, OR
*  SUPPLIED WITH THE MEDIATEK SOFTWARE, AND BUYER AGREES
 TO LOOK ONLY TO SUCH
*  THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO.
 MEDIATEK SHALL ALSO
*  NOT BE RESPONSIBLE FOR ANY MEDIATEK SOFTWARE RELEASES
 MADE TO BUYER'S
*  SPECIFICATION OR TO CONFORM TO A PARTICULAR STANDARD
 OR OPEN FORUM.
*
*  BUYER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE
 AND CUMULATIVE
*  LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED
 HEREUNDER WILL BE,
*  AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK
 SOFTWARE AT ISSUE,
*  OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE
 PAID BY BUYER TO
*  MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE.
*
*  THE TRANSACTION CONTEMPLATED HEREUNDER SHALL BE CONSTRUED
 IN ACCORDANCE
*  WITH THE LAWS OF THE STATE OF CALIFORNIA, USA, EXCLUDING
 ITS CONFLICT OF
*  LAWS PRINCIPLES.  ANY DISPUTES, CONTROVERSIES OR CLAIMS
 ARISING THEREOF AND
*  RELATED THERETO SHALL BE SETTLED BY ARBITRATION IN
 SAN FRANCISCO, CA, UNDER
*  THE RULES OF THE INTERNATIONAL CHAMBER OF COMMERCE
 (ICC).
*
*****************************************************************************/

#include <linux/string.h>

#include "lcm_drv.h"

//#include <linux/kernel.h> //for printk()

//extern void printf(const char* fmt, ...);

#ifdef BUILD_UBOOT
#include <asm/arch/mt6575_gpio.h>
#define print(x...) printf(x)
#else
#include <mach/mt6575_gpio.h>
#define print(x...) printk(x)
#endif


//libin modify for M1-4 on 20120726
#define GPIO_LCD_RST   18 //GPIO18
#define  GPIO_MODE_00  0
#define GPIO_DIR_OUT   1
#define GPIO_OUT_ONE  1
#define GPIO_OUT_ZERO  0
extern s32
 mt_set_gpio_mode(u32 u4Pin, u32 u4Mode);
extern s32
 mt_set_gpio_out(u32 u4Pin, u32 u4PinOut);
extern s32
 mt_set_gpio_dir(u32 u4Pin, u32 u4Dir);

// ---------------------------------------------------------------------------
//  Local Constants
// ---------------------------------------------------------------------------

#define FRAME_WIDTH  (320)
#define FRAME_HEIGHT (480)

// ---------------------------------------------------------------------------
//  Local Variables
// ---------------------------------------------------------------------------

static LCM_UTIL_FUNCS
 lcm_util = {0};

#define SET_RESET_PIN(v)    (lcm_util.set_reset_pin((v)))

#define UDELAY(n) (lcm_util.udelay(n))
#define MDELAY(n) (lcm_util.mdelay(n))


// ---------------------------------------------------------------------------
//  Local Functions
// ---------------------------------------------------------------------------

static __inline
 unsigned int HIGH_BYTE(unsigned int val)
{
    return (val
 >> 8) & 0xFF;
}

static __inline
 unsigned int LOW_BYTE(unsigned int val)
{
    return (val
 & 0xFF);
}

static __inline void send_ctrl_cmd(unsigned int cmd)
{
//MDELAY(5);
//mt_set_gpio_out(16, GPIO_OUT_ZERO);
    lcm_util.send_cmd(cmd);
//  mt_set_gpio_out(16, GPIO_OUT_ONE);
}

static __inline void send_data_cmd(unsigned int data)
{
//MDELAY(5);
//mt_set_gpio_out(16, GPIO_OUT_ZERO);
    lcm_util.send_data(data);
//  mt_set_gpio_out(16, GPIO_OUT_ONE);
}

static __inline
 unsigned int read_data_cmd()
{
    return lcm_util.read_data();
}

static __inline void set_lcm_register(unsigned int regIndex,
                                      unsigned int regData)
{
    send_ctrl_cmd(regIndex);
    send_data_cmd(regData);
}


static void init_lcm_registers(void)
{
send_ctrl_cmd(0xF1);
send_data_cmd(0x36);
send_data_cmd(0x04);
send_data_cmd(0x00);
send_data_cmd(0x3C);
send_data_cmd(0x0F);
send_data_cmd(0x8F);

send_ctrl_cmd(0xf2);
send_data_cmd(0x18);
send_data_cmd(0xa3);
send_data_cmd(0x12);
send_data_cmd(0x02);
send_data_cmd(0xb2);
send_data_cmd(0x12);
send_data_cmd(0xff);
send_data_cmd(0x10);
send_data_cmd(0x00);

send_ctrl_cmd(0xf8);
send_data_cmd(0x21);
send_data_cmd(0x04);

send_ctrl_cmd(0xf9);
send_data_cmd(0x00);
send_data_cmd(0x08);

send_ctrl_cmd(0xC0);
send_data_cmd(0x0F);
send_data_cmd(0x0F);

send_ctrl_cmd(0xc1);
send_data_cmd(0x42);

send_ctrl_cmd(0xC2);
send_data_cmd(0x22);

send_ctrl_cmd(0xc5);
send_data_cmd(0x00);
send_data_cmd(0x08);
send_data_cmd(0x80);

send_ctrl_cmd(0xb1);
send_data_cmd(0xB0);
send_data_cmd(0x11);

send_ctrl_cmd(0xb4);
send_data_cmd(0x02);

send_ctrl_cmd(0xb6);
send_data_cmd(0x02);
send_data_cmd(0x02); //cpu?02

send_ctrl_cmd(0xb7);
send_data_cmd(0xC6);

send_ctrl_cmd(0x3a);
send_data_cmd(0x66/*0x55*/);//16bit
 ?55  18bit  ?66

send_ctrl_cmd(0x35);
send_data_cmd(0x00);

send_ctrl_cmd(0x44);
send_data_cmd(0x00);
send_data_cmd(0x5f);

send_ctrl_cmd(0x36);
send_data_cmd(0x08); // 0xc8

send_ctrl_cmd(0x2a);
send_data_cmd(0x00);
send_data_cmd(0x00);
send_data_cmd(0x01);
send_data_cmd(0x3f);

send_ctrl_cmd(0x2b);
send_data_cmd(0x00);
send_data_cmd(0x00);
send_data_cmd(0x01);
send_data_cmd(0xdf);

send_ctrl_cmd(0xe0);
send_data_cmd(0x00);
send_data_cmd(0x1D);
send_data_cmd(0x19);
send_data_cmd(0x0c);
send_data_cmd(0x0f);
send_data_cmd(0x0A);
send_data_cmd(0x45);
send_data_cmd(0x95);
send_data_cmd(0x38);
send_data_cmd(0x0a);
send_data_cmd(0x12);
send_data_cmd(0x03);
send_data_cmd(0x09);
send_data_cmd(0x06);
send_data_cmd(0x00);

send_ctrl_cmd(0xe1);
send_data_cmd(0x0f);
send_data_cmd(0x37);
send_data_cmd(0x35);
send_data_cmd(0x0C);
send_data_cmd(0x0d);
send_data_cmd(0x04);
send_data_cmd(0x48);
send_data_cmd(0x43);
send_data_cmd(0x35);
send_data_cmd(0x04);
send_data_cmd(0x0D);
send_data_cmd(0x02);
send_data_cmd(0x1C);
send_data_cmd(0x18);
send_data_cmd(0x0F);

send_ctrl_cmd(0x11);
MDELAY(120);
send_ctrl_cmd(0x29);
send_ctrl_cmd(0x2c);
MDELAY(10);
}


// ---------------------------------------------------------------------------
//  LCM Driver Implementations
// ---------------------------------------------------------------------------

static void lcm_set_util_funcs(const LCM_UTIL_FUNCS
 *util)
{
    memcpy(&lcm_util, util, sizeof(LCM_UTIL_FUNCS));
}


static void lcm_get_params(LCM_PARAMS
 *params)
{
    memset(params, 0, sizeof(LCM_PARAMS));

    params->type   = LCM_TYPE_DBI;
    params->ctrl   = LCM_CTRL_PARALLEL_DBI;
    params->width  = FRAME_WIDTH;
    params->height = FRAME_HEIGHT;
    params->io_select_mode = 1;

    params->dbi.port                    = 0; // 1;
   //params->dbi.clock_freq              = LCM_DBI_CLOCK_FREQ_104M; 
 //aa
    params->dbi.data_width              = LCM_DBI_DATA_WIDTH_18BITS;//LCM_DBI_DATA_WIDTH_16BITS;
    params->dbi.data_format.color_order = LCM_COLOR_ORDER_RGB;
    params->dbi.data_format.trans_seq   = LCM_DBI_TRANS_SEQ_MSB_FIRST;
    params->dbi.data_format.padding     = LCM_DBI_PADDING_ON_LSB; //LCM_DBI_PADDING_ON_LSB;
 //bb
    params->dbi.data_format.format      = LCM_DBI_FORMAT_RGB666; //LCM_DBI_FORMAT_RGB565;
    params->dbi.data_format.width       = LCM_DBI_DATA_WIDTH_18BITS; //LCM_DBI_DATA_WIDTH_16BITS;
    params->dbi.cpu_write_bits          = LCM_DBI_CPU_WRITE_32_BITS; //LCM_DBI_CPU_WRITE_16_BITS;
    params->dbi.io_driving_current      = LCM_DRIVING_CURRENT_6575_8MA ;  //
 0;

  /* params->dbi.parallel.write_setup    = 1;
    params->dbi.parallel.write_hold     = 1;
    params->dbi.parallel.write_wait     = 9; // 3;
    params->dbi.parallel.read_setup     = 1;
    params->dbi.parallel.read_latency   = 31;
    params->dbi.parallel.wait_period    = 2;*/

    params->dbi.parallel.write_setup    = 2;
    params->dbi.parallel.write_hold     = 2;
    params->dbi.parallel.write_wait     = 15;
    params->dbi.parallel.read_setup     = 1;
    params->dbi.parallel.read_latency   = 31;
    params->dbi.parallel.wait_period    = 2;
     params->dbi.parallel.cs_high_width = 0;


    // enable tearing-free
  //  params->dbi.te_mode                 = LCM_DBI_TE_MODE_VSYNC_ONLY;
   // params->dbi.te_edge_polarity        = LCM_POLARITY_FALLING;

   /* params->dbi.te_mode                 = LCM_DBI_TE_MODE_VSYNC_OR_HSYNC;
    params->dbi.te_edge_polarity        = LCM_POLARITY_RISING;
    params->dbi.te_hs_delay_cnt         = 50;
    params->dbi.te_vs_width_cnt         = 277;
    params->dbi.te_vs_width_cnt_div     = LCM_DBI_TE_VS_WIDTH_CNT_DIV_16;*/


}

#define GPIO_LCD_RST   18 //GPIO18
#define  GPIO_MODE_00  0
#define GPIO_DIR_OUT   1
#define GPIO_OUT_ONE  1
#define GPIO_OUT_ZERO  0
extern s32
 mt_set_gpio_mode(u32 u4Pin, u32 u4Mode);
extern s32
 mt_set_gpio_out(u32 u4Pin, u32 u4PinOut);
extern s32
 mt_set_gpio_dir(u32 u4Pin, u32 u4Dir);
static void lcm_init(void)
{
   /* SET_RESET_PIN(0);
    MDELAY(200);
    SET_RESET_PIN(1);
    MDELAY(400);*/

     // SET_RESET_PIN(1);
   mt_set_gpio_mode(GPIO_LCD_RST,GPIO_MODE_00);
   mt_set_gpio_dir(GPIO_LCD_RST,GPIO_DIR_OUT);
   mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ONE);
    MDELAY(1);
    //SET_RESET_PIN(0);
    mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ZERO);
    MDELAY(10);
    //SET_RESET_PIN(1);
    mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ONE);
    MDELAY(100);


    init_lcm_registers();
}


static void lcm_suspend(void)
{
    send_ctrl_cmd(0x28);
    MDELAY(20);
send_ctrl_cmd(0x10);
MDELAY(100);
}


static void lcm_resume(void)
{
send_ctrl_cmd(0x11);
MDELAY(100);
send_ctrl_cmd(0x29);
//MDELAY(100);
/*
    send_ctrl_cmd(0x29);
    MDELAY(120);
send_ctrl_cmd(0x11);
MDELAY(120); */
}


static void lcm_update(unsigned int x,
 unsigned int y,
                       unsigned int width,
 unsigned int height)
{
    unsigned int x0
 = x;
    unsigned int y0
 = y;
    unsigned int x1
 = x0 + width - 1;
    unsigned int y1
 = y0 + height - 1;

print( "[LCM] *********************ili9486 lcm_update*******************

");

    send_ctrl_cmd(0x2A);
    send_data_cmd(HIGH_BYTE(x0));
    send_data_cmd(LOW_BYTE(x0));
    send_data_cmd(HIGH_BYTE(x1));
    send_data_cmd(LOW_BYTE(x1));

    send_ctrl_cmd(0x2B);
    send_data_cmd(HIGH_BYTE(y0));
    send_data_cmd(LOW_BYTE(y0));
    send_data_cmd(HIGH_BYTE(y1));
    send_data_cmd(LOW_BYTE(y1));

    // Write To GRAM
    send_ctrl_cmd(0x2C);
}

static unsigned int lcm_compare_id(void)
{
    return 1;
}
// ---------------------------------------------------------------------------
//  Get LCM Driver Hooks
// ---------------------------------------------------------------------------
LCM_DRIVER ili9486_lcm_drv =
{
    .name           = "ili9486",
    .set_util_funcs = lcm_set_util_funcs,
    .get_params     = lcm_get_params,
    .init           = lcm_init,
    .suspend        = lcm_suspend,
    .resume         = lcm_resume,
    .update         = lcm_update,
    .compare_id     = lcm_compare_id
};