• 1开机初始化配置


    ÉèÖÃadminÃÜÂë ͳһΪ cisco@123

    Enter the password for "admin":
    Confirm the password for "admin":

    ---- Basic System Configuration Dialog ----

    This setup utility will guide you through the basic configuration of
    the system. Setup configures only enough connectivity for management
    of the system.

    Please register Cisco MDS 9000 Family devices promptly with your
    supplier. Failure to register may affect response times for initial
    service calls. MDS devices must be registered to receive entitled
    support services.

    Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
    to skip the remaining dialogs.

    Would you like to enter the basic configuration dialog (yes/no): yes

    Create another login account (yes/no) [n]:

    Configure read-only SNMP community string (yes/no) [n]:

    Configure read-write SNMP community string (yes/no) [n]:

    Enter the switch name : DYNSH-DS-C9148S-B

    Continue with Out-of-band (mgmt0) management configuration? (yes/no) [y]:

    Mgmt0 IPv4 address : 10.1.1.2

    Mgmt0 IPv4 netmask : 255.255.255.0

    Configure the default gateway? (yes/no) [y]:

    IPv4 address of the default gateway : 10.1.1.1

    Configure advanced IP options? (yes/no) [n]:

    Enable the ssh service? (yes/no) [y]:

    Type of ssh key you would like to generate (dsa/rsa) [rsa]:

    Number of rsa key bits <1024-2048> [1024]:

    Enable the telnet service? (yes/no) [n]:

    Configure congestion/no_credit drop for fc interfaces? (yes/no) [y]:

    Enter the type of drop to configure congestion/no_credit drop? (con/no) [c]:

    Enter milliseconds in multiples of 10 for congestion-drop for port mode F
    in range (<100-500>/default), where default is 500. [d]:

    Congestion-drop for port mode E must be greater than or equal to
    Congestion-drop for port mode F. Hence, Congestion drop for port
    mode E will be set as default.

    Enable the http-server? (yes/no) [y]: no

    Configure clock? (yes/no) [n]: yes

    Clock config format [HH:MM:SS Day Mon YYYY] [example: 18:00:00 1 november 2012]:

    Allowed month values anuary|february|march|april|may|june|july|august|september|october|november|december]


    Enter clock config :19.3 :3 42:00 1 7 august 20176

    Configure timezone? (yes/no) [n]: yes

    Enter timezone config [PST/MST/CST/EST] :GMT
    Enter Hrs offset from UTC [-23:+23] :+8
    Enter Minutes offset from UTC [0-59] :0

    Configure summertime? (yes/no) [n]:

    Configure the ntp server? (yes/no) [n]:

    Configure default switchport interface state (shut/noshut) [shut]:

    Configure default switchport trunk mode (on/off/auto) [on]:

    Configure default switchport port mode F (yes/no) [n]:

    Configure default zone policy (permit/deny) [deny]:

    Enable full zoneset distribution? (yes/no) [n]:

    Configure default zone mode (basic/enhanced) [basic]:

    Would you like to edit the configuration? (yes/no) [n]: yes

    Use this configuration and save it? (yes/no) [y]:

    Would you like to save the running-config to startup-config? (yes/no) [n]: yes


    [# ] 1%
    [# ] 2%
    [## ] 4%
    [### ] 5%
    [### ] 6%
    [#### ] 8%
    [#### ] 9%
    [##### ] 10%
    [##### ] 12%
    [###### ] 13%
    [###### ] 14%
    [####### ] 16%
    [####### ] 17%
    [######## ] 18%
    [######### ] 20%
    [######### ] 21%
    [######### ] 22%
    [########## ] 24%
    [########### ] 25%
    [########### ] 26%
    [############ ] 28%
    [############ ] 29%
    [############# ] 30%
    [############# ] 32%
    [############## ] 33%
    [############## ] 34%
    [############### ] 36%
    [############### ] 37%
    [################ ] 38%
    [################# ] 40%
    [################# ] 41%
    [################# ] 42%
    [################## ] 44%
    [################### ] 45%
    [################### ] 46%
    [#################### ] 48%
    [#################### ] 49%
    [##################### ] 50%
    [##################### ] 52%
    [###################### ] 53%
    [###################### ] 54%
    [####################### ] 56%
    [####################### ] 57%
    [######################## ] 58%
    [######################### ] 60%
    [######################### ] 61%
    [######################### ] 62%
    [########################## ] 64%
    [########################### ] 65%
    [########################### ] 66%
    [############################ ] 68%
    [############################ ] 69%
    [############################# ] 70%
    [############################# ] 72%
    [############################## ] 73%
    [############################## ] 74%
    [############################### ] 76%
    [############################### ] 77%
    [################################ ] 78%
    [################################# ] 80%
    [################################# ] 81%
    [################################# ] 82%
    [################################## ] 84%
    [################################### ] 85%
    [################################### ] 86%
    [#################################### ] 88%
    [#################################### ] 89%
    [##################################### ] 90%
    [##################################### ] 92%
    [###################################### ] 93%
    [###################################### ] 94%
    [####################################### ] 96%
    [####################################### ] 97%
    [########################################] 98%
    [########################################] 100%
    Copy complete.

  • 相关阅读:
    静态全局变量
    java处理相对路劲
    Java 获取字符串中第N次出现的字符位置
    java 更改list 某一元素?
    for循环,如何结束多层for循环
    SQL Server Management Studio的对象资源管理器的使用
    线程
    存储过程,稍微复杂
    触发器--里面涉及触发器调存储过程
    Bootstrap:弹出框和提示框效果以及代码展示
  • 原文地址:https://www.cnblogs.com/dahaoran/p/10668642.html
Copyright © 2020-2023  润新知