smartctl hdparm lshw fdisk
badblock
软raid
mount /dev/md0 /opt
[root@localhost root]# cp /usr/share/doc/raidtools-1.00.3/raid*.conf.* /etc
[root@localhost root]# ls -l /etc/ |grep raid
[root@localhost root]# vi /etc/raid0.conf.sample
mkraid /dev/md0
mkfs.ext3 /dev/md0
lsraid -A -a /dev/md0
[root@localhost root]# more /proc/mdstat
不使用的时候请直接删除/etc/raidtab文件. # rm /etc/raidtab
有时想知道服务器上有几块磁盘，如果没有做raid，则可以简单使用fdisk -l就可以看到。但是做了raid呢，这样就看不出来了。那么如何查看服务器上做了raid？
windows：RAID卡厂商都有RAID安装程序与驱动的。在配置完RAID后，进WINDOWS系统，下载相应的RAID安装程序并安装。比如 LSI 1064E 在官网上就可以下载到。 或者HD tune可以查看基本的raid信息
linux：分软与硬
软件raid：只能通过Linux系统本身来查看cat /proc/mdstat，可以看到raid级别，状态等信息。
硬件raid：最佳的办法是通过已安装的raid厂商的管理工具来查看，有cmdline，也有图形界面。如Adaptec公司的硬件卡就可以通过下面的命令进行查看：
# /usr/dpt/raidutil -L all可以看到非常详细的信息。
当然更多情况是没有安装相应的管理工具，只能依靠Linux本身，一般有两种方式：
# dmesg |grep -i raid
# cat /proc/scsi/scsi
显示的信息差不多，raid的厂商，型号，级别，但无法查看各块硬盘的信息。
[root@coreserv log]# cat /proc/scsi/scsi
Attached devices:
Host: scsi6 Channel: 02 Id: 00 Lun: 00
Vendor: IBM Model: ServeRAID M1015 Rev: 2.13
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi7 Channel: 00 Id: 00 Lun: 00
Vendor: IBM SATA Model: DEVICE 81Y3672 Rev: SA81
Type: CD-ROM ANSI SCSI revision: 00
# fdisk -l
Disk /dev/sda: 145.9 GB, 145999527936 bytes
255 heads, 63 sectors/track, 17750 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 104391 83 Linux
/dev/sda2 14 17750 142472452+ 8e Linux LVM
# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST3146356SS Rev: HS09
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST3146356SS Rev: HS09
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi0 Channel: 01 Id: 00 Lun: 00
Vendor: Dell Model: VIRTUAL DISK Rev: 1028
Type: Direct-Access ANSI SCSI revision: 05
通过以上信息可以看出，该服务器有两块磁盘。品牌是希捷的，磁盘代号为 ST3146356SS，如果你熟悉细节磁盘的代号命名规则，你会轻易判定该磁盘大小为146G 。再根据fdisk 得出的结果可以判定，该服务器是拿两块146G的硬盘做的raid1.
不同的文件系统(xfs,reiserfs,ext3)都有自己的检测和修复工具。检测之前可以先使用dmesg命令查看有没有硬件I/O故障的日志，如果有，先用fsck看看是不是文件系统有问题，如果不是则可以使用下面介绍硬盘检测和优化方法来修复它。 grep "error" /va/log/messages*
--------------------------------------------------------------------------------------------------------------
使用SMART检测硬盘
SMART是一种磁盘自我分析检测技术，早在90年代末就基本得到了普及每一块硬盘（包括IDE、SCSI），在运行的时候都会将自身的若干参数记录下来，这些参数包括型号、容量、温度、密度、扇区、寻道时间、传输、误码率等。硬盘运行了几千小时后，很多内在的物理参数都会发生变化，某一参数超过报警阈值，则说明硬盘接近损坏，此时硬盘依然在工作，如果用户不理睬这个报警继续使用，那么硬盘将变得非常不可靠，随时可能故障。
启用SMART
SMART是和主板BIOS上相应功能配合的，要使用SMART，必须先进入到主板BIOS设置里边启动相关设置。一般从Pentium2级别起的主板，都支持SMART，BIOS启动以后，就是操作系统级别的事情了（Windows没有内置SMART相关工具,需要安装第三方工具软件)，好在Linux上很早就有了SMART支持了,如果把Linux装在VMware等虚拟机上，在系统启动时候可以看到有个服务启动报错：smartd。这个服务器就是smart的daemon进程（因为vmware虚拟机的硬盘不支持SMART，所以报错）。smartd是一个守护进程（一个帮助程序）,它能监视拥有自我监视,分析和汇报技术(Self-Monitoring, Analysis, and Reporting Technology - SMART)的硬盘。SMART体系使得硬盘能监视并汇报自己的运行状况.它的一个重要特性是能够预测失败,使得系统管理员能避免数据丢失。
[root@coreserv log]# rpm -qf /usr/sbin/smartctl
smartmontools-5.42-2.el6.x86_64
[root@coreserv log]# rpm -ql smartmontools
/etc/rc.d/init.d/smartd
/etc/smartd.conf
/etc/sysconfig/smartmontools
/usr/sbin/smartctl
/usr/sbin/smartd
/usr/sbin/update-smart-drivedb
[root@localhost ~]# smartctl --scan /dev/sda -d scsi # /dev/sda, SCSI device /dev/sdb -d scsi # /dev/sdb, SCSI device 这是一个固态盘 [root@localhost ~]# smartctl -i /dev/sda smartctl 5.43 2016-09-28 r4347 [x86_64-linux-2.6.32-431.el6.x86_64] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: Kingstek 120GB Serial Number: AA000000000000001053 LU WWN Device Id: 0 000000 000000000 Firmware Version: 20150818 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ACS-2 (revision not indicated) Local Time is: Tue Jan 8 09:26:49 2019 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled
----------------------------------------------------------------------------------------------------------------------------------
使用badblocks检测硬盘坏块
badblocks命令可以检查磁盘装置中损坏的区块。执行该指令时须指定所要检查的磁盘装置，及此装置的磁盘区块数。
badblocks -s//显示进度 -v//显示执行详细情况 /dev/sda1
# badblocks -s -v /dev/sda
正在检查从 0 到 244198583的块
Checking for bad blocks (read-only test): ^C0.10% done, 0:04 elapsed
Interrupted at block 272896
$badblocks -s//显示进度 -w//以写去检测 -v//显示执行详细情况 /dev/sda2
# badblocks -w -s -v /dev/sda1
Checking for bad blocks in read-write mode
From block 0 to 25607577
Testing with pattern 0xaa: ^C0.73% done, 0:03 elapsed
注意，不能以写的方式检测已经挂载的硬盘
----------------------------------------------------------------------------------------------------------------------------
使用hdparm测试
yum install hdparm
测试硬盘读写速度
# hdparm -Tt /dev/sda
可以查看转速，型号
[root@kvm2 ~]# hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: ST1000DM003-1ER162
Serial Number: Z4YBD720
Firmware Revision: CC45
Transport: Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
[root@kvm2 ~]# hdparm -i /dev/sda
/dev/sda:
Model=ST1000DM003-1ER162, FwRev=CC45, SerialNo=Z4YBD720
---------------------------------------------------------------------------------------------------------------------
下载安装
下载地址：ftp://download2.boulder.ibm.com/ecc/sar/CMA/XSA/ibm_utl_sraidmr_megacli-8.00.48_linux_32-64.zip
或https://docs.broadcom.com/docs-and-downloads/raid-controllers/raid-controllers-common-files/8-07-06_MegaCLI.zip
在线下载：
wget ftp://download2.boulder.ibm.com/ecc/sar/CMA/XSA/ibm_utl_sraidmr_megacli-8.00.48_linux_32-64.zip
磁硬盘阵列后如何检测和监控硬盘健康状况？
https://blog.csdn.net/enweitech/article/details/82893085
https://blog.csdn.net/xinqidian_xiao/article/details/80940306 MegaCli使用手册
wget https://docs.broadcom.com/docs-and-downloads/raid-controllers/raid-controllers-common-files/8-07-06_MegaCLI.zip unzip -d me 8-07-06_MegaCLI.zip
cd linux
rpm -ivh MegaCli-8.07.06-1.noarch.rpm
cd /opt/MegaRAID/MegaCli/
./MegaCli64 -adpcount
./MegaCli64 -AdpAllInfo -aALL
[root@kvm1 MegaCli]# ./MegaCli64 -adpcount
[root@kvm1 MegaCli]# ./MegaCli64 -AdpAllInfo -aALL
[root@kvm1 MegaCli]# ./MegaCli64 -LdPdInfo -aALL
[root@kvm1 MegaCli]# ./MegaCli64 -LDInfo -Lall -aALL
[root@kvm1 MegaCli]# ./MegaCli64 -AdpBbuCmd -aALL
命令行具体使用
[root@kvm1 MegaCli]# ./MegaCli64 -AdpAllInfo -aALL Adapter #0 ============================================================================== Versions ================ Product Name : ServeRAID M5210 Serial No : SV61224052 FW Package Build: 24.9.0-0029 Mfg. Data ================ Mfg. Date : 03/18/16 Rework Date : 00/00/00 Revision No : 04E Battery FRU : N/A Image Versions in Flash: ================ BIOS Version : 6.25.03.3_4.17.08.00_0x060E0301 FW Version : 4.290.00-4923 NVDATA Version : 3.1507.00-0011 Ctrl-R Version : 5.10-0710 Preboot CLI Version: 01.07-05:#%0000 Boot Block Version : 3.07.00.00-0002 Pending Images in Flash ================ None PCI Info ================ Controller Id : 0000 Vendor Id : 1000 Device Id : 005d SubVendorId : 1014 SubDeviceId : 0454 Host Interface : PCIE ChipRevision : C0 Link Speed : 0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 50000397081bdd32 1 50000397081b3932 2 5000c50096e01591 3 50000397a8430476 4 50000397a8430306 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 500605b00ba2c280 BBU : Absent Alarm : Absent NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 1024MB TPM : Absent On board Expander: Absent Upgrade Key : Present Temperature sensor for ROC : Present Temperature sensor for controller : Absent ROC temperature : 58 degree Celsius Settings ================ Current Time : 8:40:57 1/7, 2019 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : 1GB Cluster Mode : Disabled Alarm : Disabled Auto Rebuild : Enabled Battery Warning : Disabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Enabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : Yes Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 10 Auto Enhanced Import : Yes Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No POST delay : 90 seconds BIOS Error Handling : Stop On Errors Current Boot Mode :Normal Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID00, RAID10, RAID50, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 928 Max SGE Count : 60 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 64 Min Strip Size : 64 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 831 MB Device Present ================ Virtual Drives : 3 Degraded : 0 Offline : 0 Physical Devices : 6 Disks : 5 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : No Cluster Support : No BBU : Yes Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : Yes Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : Yes Support Boot Time PFK Change : Yes Disable Online PFK Change : Yes Support LDPI Type1 : No Support LDPI Type2 : No Support LDPI Type3 : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : Yes Block SSD Write Disk Cache Change: Yes Support Online FW Update : Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : Yes Power Savings : No Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : Yes Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 256kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : No Coercion Mode : 1GB ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : 0 Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : No Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : No Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : Yes Disable Puncturing : Yes Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : No LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : Yes Enable Led Header : No Delay during POST : 0 EnableCrashDump : Yes Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 64 Power Saving option : All power saving options are disabled Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : Yes BreakMirror RAID Support : Yes Disable Join Mirror : No Enable Shield State : Yes Time taken to detect CME : 60s Exit Code: 0x00